Wood Oil

Wood oils

Wood oils are an excellent choice for protecting, enhancing, and preserving the natural beauty of wood surfaces. Our Wood Oils category offers a wide range of high-quality wood oils, including renowned brand Osmo, known for their premium quality and eco-friendly formulations. Wood oils are ideal for use on interior and exterior wood surfaces, including furniture, flooring, decking, and more. They provide a durable, water-repellent finish that helps protect wood from moisture, UV rays, and everyday wear and tear, while also enhancing the natural color and grain of the wood. Our wood oils are made from high-quality ingredients that penetrate deeply into the wood, nourishing and protecting it from within. They are easy to apply, fast-drying, and provide long-lasting results. In addition, Osmo wood oils are known for their environmentally friendly formulations, made from natural oils and waxes that are biodegradable and free from harmful chemicals. Whether you're refinishing a piece of furniture or protecting your outdoor decking, our Wood Oils category has the right products to help you achieve a beautiful and durable finish. Explore our selection of wood oils, including Osmo, today and bring out the natural beauty of your wood surfaces!

Filter results

Osmo Country Colour Light Ochre 5ml 2203S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Light Ochre 5ml 2203 has been your wishlist!
Add to wishlist
Osmo Concrete Oil Interior Clear 5ml 610S Product Description Osmo Concrete Oil Interior Clear 5ml 610 is a clear, satin finish that provides water and dirt resistance, as well as an anti-slip surface. It is ideal for use on interior concrete surfaces, such as floors, walls, and countertops. Osmo Concrete Oil Interior Clear 5ml 610 is easy to apply and maintain, and it will help your concrete surfaces look their best for years to come. Features Provides water and dirt resistance Anti-slip surface Easy to apply and maintain Lasts for years Made from high-quality materials Backed by a trusted brand Benefits Protects your concrete surfaces from the elements Makes your concrete surfaces easier to clean and maintain Gives your concrete surfaces a beautiful, natural finish Is affordable Comes with a warranty If you are looking for a clear, satin finish that provides water and dirt resistance, as well as an anti-slip surface, then Osmo Concrete Oil Interior Clear 5ml 610 is the perfect choice for you. Order yours today!
Osmo Concrete Oil Interior Clear 5ml 610 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Clear Matt 5ml 701S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Clear Matt 5ml 701 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Teak 5ml 708S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Teak 5ml 708 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Stone Pine 5ml 710S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Stone Pine 5ml 710 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Ebony 5ml 712S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Ebony 5ml 712 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Rosewood 5ml 727S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Rosewood 5ml 727 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Red Cedar 5ml 728S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Red Cedar 5ml 728 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Fir Green 5ml 729S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Fir Green 5ml 729 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Oregon Pine 5ml 731S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Oregon Pine 5ml 731 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain White 5ml 900S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain White 5ml 900 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Patina 5ml 905S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Patina 5ml 905 has been your wishlist!
Add to wishlist
Osmo Natural Oil Woodstain Pearl Grey 5ml 906S INNOVATIVE AND DURABLE PROTECTION Base and top coat in one finish Fast drying Natural wood grain remains visible Extremely weather and UV resistant Very water and dirt resistant Resistant against algae, mould, mildew and fungal attack Reduces wood swelling and shrinkage Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 700 PINE - UV-Resistance 701 CLEAR, MATT - UV-Resistance None 702 LARCH - UV-Resistance 703 MAHOGANY - UV-Resistance 706 OAK - UV-Resistance 707 WALNUT - UV-Resistance 708 TEAK - UV-Resistance 710 STONE PINE - UV-Resistance 712 EBONY - UV-Resistance 727 ROSEWOOD - UV-Resistance 728 RED CEDAR - UV-Resistance 729 FIR GREEN - UV-Resistance 731 OREGON PINE - UV-Resistance 732 LIGHT OAK - UV-Resistance 900 WHITE - UV-Resistance 903 BASALT GREY - UV-Resistance 905 PATINA - UV-Resistance 906 PEARL GREY - UV-Resistance 907 QUARTZ GREY - UV-Resistance FINISHES Various colour (Satin), Clear (Matt) APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME First coat: 4-6 hours, Second coat: 12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones. Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone. Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas. The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Natural Oil Woodstain Pearl Grey 5ml 906 has been your wishlist!
Add to wishlist
Osmo Country Colour Medium Brown 5ml 2606S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Medium Brown 5ml 2606 has been your wishlist!
Add to wishlist
Osmo Opaque Gloss Wood Stain White 5ml 2104S WHITE GLOSS FRAMING Extremely weather and UV resistant Suitable for interior and exterior framework Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2104 WHITE, GLOSS FINISHES White Gloss APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Interior and exterior wood frames RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRYING TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 20m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Opaque Gloss Wood Stain is ready to use. Do not thin. Stir well. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE When used in dark indoor areas, the coating has due to its high oil content a slight yellowing effect. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Spray-Cleaner. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Opaque Gloss Wood Stain White 5ml 2104 has been your wishlist!
Add to wishlist
Osmo Country Colour Light Grey 5ml 2735S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Light Grey 5ml 2735 has been your wishlist!
Add to wishlist
Osmo Country Colour Dusk Grey 5ml 2704S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Dusk Grey 5ml 2704 has been your wishlist!
Add to wishlist
Osmo Country Colour Charcoal 5ml 2703 Brand: Osmo   Color: Charcoal Size: 5ml SKU: 2703S Features: Water-based, oil-modified wood stain Provides a long-lasting, natural finish Easy to apply and maintain Suitable for use on interior wood surfaces Benefits: Protects your wood surfaces from the elements Makes your wood surfaces easier to clean and maintain Gives your wood surfaces a beautiful, natural finish Is affordable Comes with a warranty Application: Prepare the wood surface by cleaning it with a damp cloth and removing any dirt, dust, or grease. Apply the Osmo Country Colour Charcoal 5ml 2703 with a brush or roller, working in the direction of the wood grain. Allow the first coat to dry completely before applying a second coat, if desired. For best results, apply a third coat after 24 hours. Maintenance: Osmo Country Colour Charcoal 5ml 2703 can be refreshed with a light coat of furniture polish every few months.
Osmo Country Colour Charcoal 5ml 2703 has been your wishlist!
Add to wishlist
Osmo Country Colour Dark Brown 5ml 2607 Brand: Osmo Color: Dark Brown Size: 5ml SKU: 2607S Features: Water-based, oil-modified wood stain Provides a long-lasting, natural finish Easy to apply and maintain Suitable for use on interior wood surfaces Benefits: Protects your wood surfaces from the elements Makes your wood surfaces easier to clean and maintain Gives your wood surfaces a beautiful, natural finish Is affordable Comes with a warranty Application: Prepare the wood surface by cleaning it with a damp cloth and removing any dirt, dust, or grease. Apply the Osmo Country Colour Dark Brown 5ml 2607 with a brush or roller, working in the direction of the wood grain. Allow the first coat to dry completely before applying a second coat, if desired. For best results, apply a third coat after 24 hours. Maintenance: Osmo Country Colour Dark Brown 5ml 2607 can be refreshed with a light coat of furniture polish every few months. Additional Information: Osmo Country Colour Dark Brown 5ml 2607 is a small sample size, perfect for testing the color and application of the product before purchasing a larger quantity. The sample size is also ideal for touch-ups or small projects. Osmo Country Colour Dark Brown 5ml 2607 is available for purchase online and at select retailers.
Osmo Country Colour Dark Brown 5ml 2607 has been your wishlist!
Add to wishlist
Osmo Country Colour Cedar/Redwood 5ml 2310S Water-Based, Oil-Modified Wood Stain Sample Description: Osmo Country Colour Cedar/Redwood 5ml 2310 is a water-based, oil-modified wood stain that provides a long-lasting, natural finish. It is ideal for use on interior wood surfaces, such as furniture, floors, and walls. Osmo Country Colour Cedar/Redwood 5ml 2310 is easy to apply and maintain, and it will help your wood surfaces look their best for years to come. Features: Water-based, oil-modified formula Provides a long-lasting, natural finish Easy to apply and maintain Suitable for use on interior wood surfaces Available in a variety of colors, including Cedar/Redwood Benefits: Protects your wood surfaces from the elements Makes your wood surfaces easier to clean and maintain Gives your wood surfaces a beautiful, natural finish Is affordable Comes with a warranty Application: Prepare the wood surface by cleaning it with a damp cloth and removing any dirt, dust, or grease. Apply the Osmo Country Colour Cedar/Redwood 5ml 2310 with a brush or roller, working in the direction of the wood grain. Allow the first coat to dry completely before applying a second coat, if desired. For best results, apply a third coat after 24 hours. Maintenance: Osmo Country Colour Cedar/Redwood 5ml 2310 can be refreshed with a light coat of furniture polish every few months.
Osmo Country Colour Cedar/Redwood 5ml 2310 has been your wishlist!
Add to wishlist
Osmo Country Colour Ivory 5ml 2204S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Ivory 5ml 2204 has been your wishlist!
Add to wishlist
Osmo Country Colour Sunflower Yellow 5ml 2205S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Sunflower Yellow 5ml 2205 has been your wishlist!
Add to wishlist
Elevate Your Interior with Osmo Polyx-Oil Effect Raw 5ml (3044S) Unlock the Magic of Wood's True Beauty Experience the enchantment of wood in its purest form with Osmo Polyx-Oil Effect Raw 5ml. This innovative wood finish allows you to showcase the authentic texture and allure of wood while providing unmatched protection. Unleash Enduring Excellence Osmo Polyx-Oil Effect Raw 5ml not only preserves the wood's inherent charm but also defends it against daily challenges. Its exceptional durability and resistance to water, stains, and spills ensure your wood retains its splendor for years to come. Embrace Wood's Soulful Elegance Let the character of the wood shine through with Osmo Polyx-Oil Effect Raw 5ml. Its microporous, breathable finish creates a seamless, crack-resistant surface that enhances wood's grace without peeling, flaking, or fading. Easy Application, Lasting Impact Applying Osmo Polyx-Oil Effect Raw 5ml is effortless. Choose from an Osmo Flat Brush, Floor Brush, Osmo Microfibre Roller, or FloorXcenter for a smooth, even finish. Ideal for interior wooden flooring and furniture, this finish elevates your space with its natural allure. Swift Drying, Simple Cleanup Experience swift drying within 24 hours, enabling you to enjoy your revitalized wood sooner. Cleanup is a breeze with Osmo Brush Cleaner, ensuring your tools remain in pristine condition for future projects. Generous Coverage, Timeless Beauty Revel in remarkable coverage with Osmo Polyx-Oil Effect Raw 5ml – approximately 30m² per liter with a single coat. Apply two coats, or one coat and a top coat of Polyx Oil Original, to achieve an exceptional finish that stands the test of time. Preserve and Nurture: Caring for Your Wood Sustain the splendor of your wood surfaces with Osmo Wash and Care or Spray-Mop. This care regimen nurtures and protects your wood's natural beauty, ensuring it remains captivating for generations. Discover Wood's Essence: Go Raw with Osmo Uncover the timeless allure of wood in your living spaces with Osmo Polyx-Oil Effect Raw 5ml (3044S). Elevate your interior design with a finish that celebrates the authentic essence of wood while safeguarding its elegance. Disclaimer: The information provided is based on product details available at the time of writing. It is recommended to verify specifications, coverage, and application instructions before use. Colors may vary due to screen settings and lighting conditions. Always adhere to safety precautions and consult the manufacturer's guidelines for the best results. Unlock the Beauty of Raw Wood – Order Osmo Polyx-Oil Effect Raw 5ml Today!
Osmo Polyx -Oil Effect Raw 5ml 3044 has been your wishlist!
Add to wishlist
Osmo Country Colour Signal Red 5ml 2311S COLOURFUL DIVERSITY Extremely weather and UV resistant Very water and dirt resistant Reduces wood swelling and shrinkage Natural wood grain is hidden Microporous, breathable finish which does not crack, peel or flake No sanding necessary for future applications 2101 WHITE 2203 LIGHT OCHRE 2204 IVORY 2205 SUNFLOWER YELLOW 2308 NORDIC RED 2310 CEDAR/REDWOOD 2311 SIGNAL RED 2404 FIR GREEN 2501 LABRADOR BLUE 2506 ROYAL BLUE 2507 DOVE BLUE 2606 MEDIUM BROWN 2607 DARK BROWN 2703 CHARCOAL 2704 DUSK GREY 2708 PEBBLE GREY 2716 ANTHRACITE GREY 2735 LIGHT GREY 2742 TRAFFIC GREY FINISHES Opaque White, Light Ochre, Ivory, Sunflower Yellow, Nordic Red, Cedar/Redwood, Signal Red, Fir Green, Labrador Blue, Royal Blue, Dove Blue, Medium Brown, Dark Brown, Charcoal, Dusk Grey, Pebble Grey, Anthracite Grey, Light Grey, Traffic Grey APPLICATION TOOL Osmo Flat Brush or Osmo Microfibre Roller RECOMMENDED USE Exterior wood surfaces RECOAT One coat, when signs of wear become visible SIZES 5ml, 125ml, 750ml, 2.5L DRY TIME 10-12 hours CLEAN UP Osmo Brush Cleaner COVERAGE 26m²/L with one coat COATS 2 coats CARE Osmo Spray Cleaner (Exterior) SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Country Colour is ready to use. Do not thin. Stir well before use. If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. Allow to dry for approx. 10-12 hours under good ventilation. After drying, apply a second coat – also thinly. For renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE If surfaces in outdoor areas (e.g. windows, cladding) should have additional protection, apply one top coat of Osmo UV-Protection-Oil Clear (410 without film protection or 420 with film protection) after thoroughly drying. This protects against dirt contamination and extends the life of the finish. For Country Colour White 2101, please use Natural Oil Woodstain White 900. Country Colour, which has been trusted for over decades, is also available in the colour of your choice. Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones, as well as with biocidal film protection additives. Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning:  Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush. Occasional Maintenance:  If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating:  Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.
Osmo Country Colour Signal Red 5ml 2311 has been your wishlist!
Add to wishlist
  • 1
  • 2
  • 3
  • 4
    • ...
  • Next
  • Showing 1 - 24 of 445 results

© Eakers DIY 2024.
Online Shop Builder & ePOS System by ShopTill-e.com